16.4.6 Packet Tracer – Configure Secure Passwords and SSH Instructor Version
16.4.6 Packet Tracer – Configure Secure Passwords and SSH
Addressing Table
| Device | Interface | IP Address | Subnet Mask | Default Gateway |
|---|---|---|---|---|
| RTA | G0/0 | 172.16.1.1 | 255.255.255.0 | N/A |
| PCA | NIC | 172.16.1.10 | 255.255.255.0 | 172.16.1.1 |
| SW1 | VLAN 1 | 172.16.1.2 | 255.255.255.0 | 172.16.1.1 |
Scenario
The network administrator has asked you to prepare RTA and SW1 for deployment. Before they can be connected to the network, security measures must be enabled.
Intructions
Step 1: Configure Basic Security on the Router
a. Configure IP addressing on PCA according to the Addressing Table.
b. Console into RTA from the Terminal on PCA.
c. Configure the hostname as RTA.
d. Configure IP addressing on RTA and enable the interface.
e. Encrypt all plaintext passwords.
RTA(config)# service password-encryption
f. Set the minimum password length to 10.
RTA(config)# security password min-length 10
g. Set a strong secret password of your choosing.
Note: Choose a password that you will remember, or you will need to reset the activity if you are locked out of the device.
h. Disable DNS lookup.
RTA(config)# no ip domain-lookup
i. Set the domain name to CCNA.com (case-sensitive for scoring in PT).
RTA(config)# ip domain-name CCNA.com
j. Create a user of your choosing with a strong encrypted password.
RTA(config)# username any_user secret any_password
k. Generate 1024-bit RSA keys.
Note: In Packet Tracer, enter the crypto key generate rsa command and press Enter to continue.
RTA(config)# crypto key generate rsa
The name for the keys will be: RTA.CCNA.com
Choose the size of the key modulus in the range of 360 to 2048 for your
General Purpose Keys. Choosing a key modulus greater than 512 may take
a few minutes.
How many bits in the modulus [512]: 1024
l. Block anyone for three minutes who fails to log in after four attempts within a two-minute period.
RTA(config)# login block-for 180 attempts 4 within 120
m. Configure all VTY lines for SSH access and use the local user profiles for authentication.
RTA(config)# line vty 0 4
RTA(config-line)# transport input ssh
RTA(config-line)# login local
n. Set the EXEC mode timeout to 6 minutes on the VTY lines.
RTA(config-line)# exec-timeout 6
o. Save the configuration to NVRAM.
p. Access the command prompt on the desktop of PCA to establish an SSH connection to RTA.
(Make sure you have IP configured for PCA)
C:\> ssh /?
Packet Tracer PC SSH
Usage: SSH -l username target
C:\>
C:\>SSH -l jony 172.16.1.1
Password: <~~ enter password itexamanswers.net
Step 2: Configure Basic Security on the Switch
Configure switch SW1 with corresponding security measures. Refer to the configuration steps on the router if you need additional assistance.
a. Click on SW1 and select the CLI tab.
b. Configure the hostname as SW1.
c. Configure IP addressing on SW1 VLAN1 and enable the interface.
d. Configure the default gateway address.
e. Disable all unused switch ports.
Note: On a switch it is a good security practice to disable unused ports. One method of doing this is to simply shut down each port with the ‘shutdown’ command. This would require accessing each port individually. There is a shortcut method for making modifications to several ports at once by using the interface range command. On SW1 all ports except FastEthernet0/1 and GigabitEthernet0/1 can be shutdown with the following command:
SW1(config)# interface range F0/2-24, G0/2
SW1(config-if-range)# shutdown
%LINK-5-CHANGED: Interface FastEthernet0/2, changed state to administratively down
%LINK-5-CHANGED: Interface FastEthernet0/3, changed state to administratively down
<Output omitted>
%LINK-5-CHANGED: Interface FastEthernet0/24, changed state to administratively down
%LINK-5-CHANGED: Interface GigabitEthernet0/2, changed state to administratively down
The command used the port range of 2-24 for the FastEthernet ports and then a single port range of GigabitEthernet0/2.
f. Encrypt all plaintext passwords.
g. Set a strong secret password of your choosing.
h. Disable DNS lookup.
i. Set the domain name to CCNA.com (case-sensitive for scoring in PT).
j. Create a user of your choosing with a strong encrypted password.
k. Generate 1024-bit RSA keys.
l. Configure all VTY lines for SSH access and use the local user profiles for authentication.
m. Set the EXEC mode timeout to 6 minutes on all VTY lines.
n. Save the configuration to NVRAM.
Final Script – Download PDF & PKA file:
[sociallocker id=”54558″]
Router RTA
enable
config terminal
hostname RTA
interface g0/0
ip address 172.16.1.1 255.255.255.0
no shutdown
exit
service password-encryption
security password min-length 10
enable secret itexamanswers
no ip domain-lookup
ip domain-name CCNA.com
username jony secret itexamanswers.net
crypto key generate rsa
1024
login block-for 180 attempts 4 within 120
line vty 0 4
transport input ssh
login local
exec-timeout 6
end
copy running-config startup-config
Switch SW1
enable
config terminal
hostname SW1
interface vlan 1
ip address 172.16.1.2 255.255.255.0
no shutdown
exit
ip default-gateway 172.16.1.1
interface range F0/2-24, G0/2
shutdown
exit
service password-encryption
enable secret class
no ip domain-lookup
ip domain-name CCNA.com
crypto key generate rsa
1024
username admin_switch secret p@ssword
line vty 0 15
transport input ssh
login local
exec-timeout 6
end
copy running-config startup-config
IP configured for PCA
